Delta 36-444 Manual de instrucciones

INSTRUCTION MANUAL10″″Contractor’s Saw(Model 36-444, 36-445)PART NO. 422-19-651-0048 - 10-18-02Copyright © 2002 Delta MachineryTo learn more about DEL

10MOTORThe motor supplied with your saw is a 1-1/2 H.P. at 115 volts or 2 H.P. at 230 volts, Ball Bearing,Capacitor Start/Capacitor Run, motor. This m

11Fig. 16Fig. 17ASSEMBLING MOTORPULLEY, BELT ANDPULLEY GUARD, ANDDRIVE BELTWARNING: DISCONNECT MACHINE FROMPOWER SOURCE.1. Remove the motor shaft key

12Fig. 21WARNING: IMMEDIATELY AFTER ASSEMBLINGTHE BELT, RAISE THE SAW BLADE TO ITS MAXIMUMHEIGHT AND TILT THE SAW BLADE TO 45 DEGREES.CHECK TO SEE IF

13REPOSITIONING MOTOR FOR STORAGEWhen the saw is not in use, the motor can be repositioned so it hangs straight down at therear, enabling you to move

14Fig. 28DEFig. 29Fig. 304. Using a straight edge, check to see if the top andbottom of the inside splitter bracket (D) Fig. 28, isaligned with the in

15Fig. 34Fig. 35GGAFig. 3610. Using a straight edge, check to see if the saw bladeis aligned with the rear of the splitter (G), as shown inFigs. 34 an

16FASTENING STAND TO SUPPORTING SURFACEWARNING: IF DURING OPERATION THERE IS ANY TENDENCY FOR THE SAW TO TIP OVER, SLIDE ORWALK ON THE SUPPORTING SURF

17Fig. 42Fig. 43RAISING AND LOWERINGTHE BLADETo raise the saw blade, loosen lock knob (A) Fig. 42, andturn the blade raising handwheel (B) clockwise.

18BACKLASH ADJUSTMENTSFOR BLADE RAISING ANDBLADE TILTINGMECHANISMSIf any play is detected in the blade raising or blade tiltingmechanisms, the followi

19Fig. 49Fig. 50Fig. 51Fig. 52ADJUSTING TABLE INSERTWARNING: DISCONNECT MACHINE FROMPOWER SOURCE.Place a straight edge across the table at both ends o

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

20Fig. 53Fig. 54Fig. 55Fig. 56CHANGING THESAW BLADEWARNING: DISCONNECT MACHINE FROMPOWER SOURCE.1. NOTE: Two 7/8″ wrenches are supplied with the sawfo

21OPERATIONSCommon sawing operations include ripping and cross-cutting, plus a few other standard operations of afundamental nature. As with all power

22CLAMP ATTACHMENTFOR MITER GAGEThe Clamp Attachment, shown in Fig. 60, is available asan accessory for your miter gage. The clamp attachmentcan easil

23Fig. 643. Ripping narrow pieces can be dangerous if not donecarefully. Narrow pieces usually cannot be cut with theguard in position. If the workpie

24USING ACCESSORYDADO HEADDadoing is cutting a rabbet or wide groove into thework. Most dado head sets are made up of two outsidesaws and four or five

25CONSTRUCTING A FEATHERBOARDFig. 73, illustrates dimensions for making a typical featherboard. The material which the featherboard is constructed of,

26CONSTRUCTING A PUSH STICKWhen ripping work less than 4 inches wide, push sticks should be used to complete the feed and can easily be madefrom scra

27BLADE GUARD ACCESSORIESDeluxe Uniguard®Blade GuardThe Delta Model 34-976 Uniguard Blade Guard withSplitter and Anti-kickback Fingers Fig. 75, is ana

28Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory which

29NOTES

3ADDITIONAL SAFETY RULES FORTABLE SAWSWARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.SAVE THESE INSTRUCTIONS. Refer to t

30NOTES

31NOTES

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

4POWER CONNECTIONSA separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should beprotected wi

5Use proper extension cords. Make sure your extensioncord is in good condition and is a 3-wire extension cordwhich has a 3-prong grounding type plug a

6UNPACKING AND CLEANINGCarefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from themachined

7Fig. 3123456789101. Combination Dust Chute/Support Panel2. Motor Pulley3. Motor4. Pulley Guard5. Drive Belt6. Motor Mounting Plate7. Rear Leg Panel8.

8ASSEMBLY INSTRUCTIONSWARNING: MAKE SURE THE SAW IS SECURELY ATTACHED TO THE STAND BEFORE PERFORMING ANYCUTTING OPERATIONS. DO NOT OPERATE THIS MACHIN

9Fig. 9Fig. 10Fig. 11ASSEMBLING BLADETILTING HANDWHEEL1. Assemble blade tilting handwheel (A) Fig. 10, toshaft (B). Make certain slot (C) in handwheel