Delta 1.07 VFD-D D Manual de usuario Pagina 48
- Pagina / 141
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 4 Parameter Settings|DD Series
4-24
4-2 Description of Parameter Settings
00 System Parameter This parameter can be set during operation.
Identity Code of AC Motor Drive
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: Read only
Settings
0:200w
1:400w
Rated Current Display of AC Motor Drive
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: Read only
Settings 0:1.50A
2:2.50A
Pr. 00-00 displays the identity code of the AC motor drive. The capacity, rated current, rated voltage and
the max. carrier frequency relate to the identity code. Users can use the following table to check how the
rated current, rated voltage and max. carrier frequency of the AC motor drive corresponds to the identity
code.
Pr.00-01 displays the rated current of the AC motor drive. By reading this parameter the user can check if
the AC motor drive is correct.
Parameter Reset
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0
Settings
0: No function
1: Parameters locked
8: Keypad locked
10: All parameters are reset to factory setting (33.3Hz, 230V)
When it is set to 1, all parameters are read only except Pr.00-00~00-07 and it can be used with password
setting for password protection.
When Pr.00-02=10, all parameters are reset to factory setting. If password lock was used, please unlock
first. After Pr.00-02 set to 10, password will also be cleared and reset to factory setting.
When Pr.00-02=08, the digital keypad will be locked and only Pr.00-02, Pr.00-07 can be set.
Start-up Display Selection
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 0
Settings
0: Display the frequency command value (F)
1: Display the actual output frequency (H)
2: Display the content of user-defined unit (U)
3: Display the output current (A)
This parameter determines the start-up display page after power is applied to the drive.
Content of Multi Function Display
Control mode VF VFPG SVC FOCPG FOCPM
Factory setting: 2
Settings
0: Display output current (A )
1: Display actual frequency (Hz)
2: Display DC-BUS voltage ( U)
3: Display output voltage( E )
4: Display power factor angle (n.)
- ''( 1
- 1
- Preface 2
- Table of Content 5
- Chapter 1 Introduction 7
- 1-1 Receiving and Inspection 8
- T02DD21A0 9
- Minimum Mounting Clearances 10
- CAUTION! 11
- Dimensions for Motor 12
- ECMD-B9160GMS 13
- Chapter 2 Wiring 14
- 2-1 Wiring Diagram 15
- Used with external power 16
- Not allowed 17
- 2-2 Main Circuit Terminal 18
- Chapter 2 Wiring 19
- 2-3 Control Circuit Terminal 20
- 3-1 Operation Method 23
- 3-2 Keypad Descriptions 24
- Chapter 4 Parameter Settings 25
- Settings 28
- Parameter Reset 48
- Start-up Display Selection 48
- Software version 49
- Password Input 49
- Password Set 49
- Control Method 50
- Door Control Mode 51
- Output Direction 52
- Demo Mode 53
- Frequency Testing Command 53
- Motor Auto Tuning (PM) 55
- Motor Auto Tuning (IM) 57
- Output Voltage 3 61
- Output Frequency 4 61
- Output Voltage 4 61
- OD:("OPEN":STOP) 62
- CD:(" OPEN": STOP) 62
- Multi-function Output (MO3) 65
- Digital Output Direction 66
- Position Detection Signal 1 66
- Encoder (PG) Signal Type 68
- Encoder pulse 68
- Encoder Input Type Setting 68
- Door Width Pulses (Unit:1) 70
- 04.19=S1 73
- 04.20=S2 73
- Freqeunc 73
- VFPG SVC FOCPG 74
- 05.19=S1 77
- 05.20=S2 77
- Door Re-open Detection Time 79
- Quadrant I 80
- Quadrant II 80
- Quadrant III 80
- Quadrant IV 80
- Low Voltage Level 81
- Position Control Mode 82
- VFPG SVC FOCPG FOCPM 84
- Auto Restart After Fault 85
- Gain for Speed Feed Forward 88
- VFPG SVC FOCPG FOCPM 89
- Communication Address 90
- Transmission Speed 90
- Transmission Fault Treatment 90
- Time-out Detection 90
- Communication Protocol 90
- Code Description: 91
- Status monitor 97
- Read only 97
- Example: 98
- Response Delay Time 99
- Multi-function Output RY1 103
- Multi-function Output RY2 103
- View User-defined Parameters 103
- 2 1 1B 104
- 111x16 + x16 =16+11 = 104
- Enter 2127 104
- Chapter 5 Troubleshooting 106
- 5-1 Over Current (oc) 107
- 5-2 Ground Fault (GFF) 108
- 5-3 Over Voltage (ov) 109
- 5-4 Low Voltage (Lv) 110
- 5-5 Over Heat (oH1) 111
- 5-6 Overload (oL) 112
- 5-8 Phase Loss (PHL) 114
- 5-9 Motor is not Running 115
- 5-12 Motor Run Error 118
- 5.14 Environmental Condition 120
- High Harmonic at Power Side 121
- Motor Temperature Rises 121
- 6.1.1 Reset 127
- Voltage 128
- Keypad 128
- Mechanical parts 128
- Main circuit 129
- Resistor of main circuit 130
- Control Characteristics 132
- Motor Model 134
- Appendix B 135
- B-1 Capacity Formulas 136
- Symbol explanation 137
- B-2 General Precautions 138
- Drives Selection 138
- Parameter Settings 138
- Standard motor 139
- Special motors: 140
- Power Transmission Mechanism 140
- Motor torque 141
© 2020, manymanuals.es. Todos los derechos reservados | 1.727 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales