Delta 50-868 Manual de usuario descargar pdf (Pagina 3)

13. DO NOT ATTEMPT TO REMOVE OR REPLACE THE FILTER(S) WHILE THE UNIT IS RUNNING. Make certain

that the unit is disconnected from the power source.

14. MAINTAIN THE UNIT IN TOP CONDITION. Keep filters clean for optimum performance. Follow all instructions for

changing and cleaning filters.

15. STORE THIS UNIT IN A LOCATION that eliminates the potential of damage to the power cord. Safely store power

cord on the unit to eliminate tripping hazards.

16. TURN THE UNIT “OFF” AND DISCONNECT IT FROM THE POWER SOURCE before installing or removing

accessories, or when making repairs.

READ AND SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others

GROUNDING INSTRUCTIONS

THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM

ELECTRIC SHOCK.

2. Grounded, cord-connected tools intended for use

on a supply circuit having a nominal rating less than

150 volts:

This tool is intended for use on a normal 120-volt circuit

and has a grounded plug that looks like the plug illustrat-

ed in Fig. A.

If a properly grounded outlet is not available, a temporary

adapter, shown in Fig. B, may be used for connecting the

3-prong grounding type plug to a 2-hole receptacle. The

temporary adapter should be used only until a properly

grounded outlet can be installed by a qualified electrician.

The green colored rigid ear, lug, or the like extending from

the adapter must be connected to a permanent ground

such as a properly grounded outlet box cover. Whenever

the adapter is used, it must be held in place with a metal

screw.

NOTE: In Canada, the use of a temporary adapter is

not permitted by the Canadian Electric Code.

IN ALL CASES, MAKE CERTAIN THE

RECEPTACLE IN QUESTION IS

PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE

A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

1. All grounded, cord-connected tools:

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current to

reduce the risk of electric shock. This tool is equipped

with an electric cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into a matching outlet that is properly installed

and grounded in accordance with all local codes and ordi-

nances.

Do not modify the plug provided - if it will not fit the

outlet, have the proper outlet installed by a qualified

electrician.Improper connection of the equipment-

grounding conductor can result in risk of electric shock.

The conductor with insulation having an outer surface that

is green with or without yellow stripes is the equipment-

grounding conductor. If repair or replacement of the

electric cord or plug is necessary, do not connect the

equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel

if the grounding instructions are not completely under-

stood, or if in doubt as to whether the tool is properly

grounded.

Use only 3-wire extension cords that have 3-prong

grounding type plugs and 3-hole receptacles that accept

the tool’s plug, as shown in Fig. A.

Repair or replace damaged or worn cord immediately.

POWER CONNECTIONS

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should

be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-

prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the unit

to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same

characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage

will damage the unit.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

MOTOR SPECIFICATIONS

Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source,

make sure the switch is in the “OFF” position. The full-load current is 5.0 amps.

1 2 3 4 5 6 7 8 9 10 11

Comentarios a estos manuales

Sin comentarios

Delta 50-868 Manual de usuario Pagina 3

Comentarios a estos manuales