Delta 36-220 Manual de instrucciones

INSTRUCTION MANUAL10" Compound Miter Saw(Model 36-220)PART NO. 900327 - 01-01-01Copyright © 2001 Delta MachineryESPAÑOL: PÁGINA 23To learn more a

10Fig. 17Fig. 16Fig. 15ROTATING TABLEFOR MITER CUTTINGYour compound miter saw will cut any miter angle from astraight 90 degree cut-off to 47 degrees

11Fig. 18LOCKING CUTTING ARMIN THE DOWN POSITIONWhen transporting the saw, the cutting arm shouldalways be locked in the down position. This can beacc

12Fig. 22Fig. 21ADJUSTMENTSADJUSTING 90 AND 45DEGREE BEVEL STOPS1. DISCONNECT THE SAW FROM THE POWERSOURCE.2. Loosen bevel lock handle and tilt the cu

13Fig. 26ADJUSTING BLADEPARALLEL TO TABLE SLOT1. DISCONNECT THE SAW FROM THE POWERSOURCE.2. NOTE: This adjustment should be checked with thecutting ar

14Fig. 28Fig. 297. Loosen the two fence locking screws, one of which isshown at (A) Fig. 28, and move the fence (B) all the wayto the rear position, a

15Fig.31Fig. 32Fig. 33ADJUSTING DOWNWARDTRAVEL OF SAW BLADE1. DISCONNECT THE SAW FROM THE POWERSOURCE.2. The downward travel of the saw blade can be l

16Fig. 34Fig. 35Fig. 369. Fig. 34, illustrates the work clamp (B) being used tofirmly hold the workpiece against the fence.10. Fig. 35, illustrates th

17Fig. 37 Fig. 38Fig. 39When performing multiple or repetitive cut-off operationsthat result in small cut-off pieces, one inch or less, it ispossible

18Fig. 43MAINTENANCECHANGING THE BLADEWARNING: USE ONLY CROSS-CUTTING SAWBLADES. WHEN USING CARBIDE TIPPED BLADES,MAKE SURE THEY HAVE A NEGATIVE HOOK

19Fig. 44Fig. 45BRUSH INSPECTIONAND REPLACEMENTCAUTION: BEFORE INSPECTING BRUSHES, DIS-CONNECT THE MACHINE FROM THE POWERSOURCE.Brush life varies. It

2SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards in

20Delta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin normal use has proven

21NOTES

22NOTES

The following are trademarks of PORTER-CABLE•DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE S.A.):BAMMER®, INNOVATION THAT W

ADDITIONAL SAFETY RULES FORCOMPOUND MITER SAWS31. USE ONLY CROSS-CUTTING SAW BLADES.WHEN USING CARBIDE TIPPED BLADES, MAKESURE THEY HAVE A NEGATIVE HO

4CONNECTING COMPOUND MITER SAWTO POWER SOURCEYour new Compound Miter Saw is DOUBLE INSULATED to give you added safety. As a result, this saw is equipp

5OPERATING INSTRUCTIONSFOREWORDDelta Model 36-220 is a 10" Compound Miter Saw designed to cut wood. It can crosscut up to 2-3/4" x 5-1/8&quo

6Fig. 2Fig. 3Fig. 41. Push down on the cuttinghead handle slightly androtate latch (A) Fig. 2, to the other side.2. The cuttinghead will then move to

7Fig. 5ASSEMBLING STOCK STOPAND TABLE EXTENSIONS1. Decide on which side of the saw table you want thestock stop (A) Fig. 5, to be, and assemble stock

8Fig. 12Fig. 11Fig. 10Fig. 9ASSEMBLING ACCESSORYWORK CLAMP TO SAW1. The work clamp (A) Fig. 9, can be used on either theright or left side of the saw

9STARTING ANDSTOPPING SAWTo turn the saw “ON” push in on switch lock key (A) Fig.13, and depress switch trigger (B). To turn the saw “OFF”release swit