Delta SA446 Manual de instrucciones

INSTRUCTION MANUALPART NO. A05754 - 04-18-05Copyright © 2005 Delta MachineryESPAÑOL: PÁGINA 23To learn more about DELTA MACHINERY visit our website at

10Attach the belt and pulley guard (A) Fig. 4 to the machinebase using the two M6x1x30mm cheese head screws(B).1. Turn the 1/4-20 x 1/4" hex sock

111. Clean the sanding disc plate (A) Fig. 8.2. Peel the backing from sanding disc and press thedisc (B) firmly into position all the way around thesa

12Align the three holes in the dust chute (A) Fig. 12 with thethree holes in the left side of the sanding base. Place anM5.3 flat washer on an M5 x .0

133. Alternately, you can secure the sander by fasteningit to a mounting board 18" x 24" or larger. Thediagram in Fig. 16 shows the size and

141. Turn the switch “ON” to see if the sanding beltmoves to one side or the other on the sandingdrums. If the belt rides on the center of the sanding

151. Before adjusting, move the belt tension lever (A) Fig. 23 all the way to the left to the "TIGHTEN" position.2. Place a square (B) Fig.

162. To adjust, loosen the three screws (B) Fig. 29 thatfasten the table to the table mounting bracket andtrunnion. Adjust the table accordingly - the

17When you use the sanding arm (A) Fig. 31 in the vertical position, you can move the complete table assembly (B) fromthe disc unit to the belt unit.T

181. Loosen the screw (A) Fig. 34 and remove the backstop (B).2. Slide the tension lever (C) Fig. 35 to the right to release the tension on the sandin

19MACHINE USESURFACING OR EDGE SANDING WITH THE SANDING BELTAlways use the backstop (A) Figs. 39 and 40 when surface-sanding (Fig. 39) or when edge sa

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20END SANDING WITH THE BELTWhen sanding the ends of wide workpieces, use the sanding belt with the sanding arm in the vertical position and thetable a

21MAINTENANCEPARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a

22Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5ADDITIONAL SPECIFIC SAFETY RULES1. DO NOT OPERATE THIS MACHINE until it iscompletely assembled and installed according to theinstructions. A machine

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

7EXTENSION CORDSUse proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong groun

8UNPACKING AND CLEANINGCarefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating fromall unpainte

9ASSEMBLYASSEMBLY TOOLS REQUIREDASSEMBLY TIME ESTIMATE1/8" Hex Wrench (Supplied)6 Mm Hex Wrench (Supplied) Phillips ScrewdriverAdjustable WrenchL