Delta 36-585 Manual de instrucciones

INSTRUCTION MANUAL10" Dual Bevel CompoundMiter Saw(Model 36-585)PART NO. 910638 - 01-30-04Copyright © 2004 Delta MachineryESPAÑOL: PÁGINA 21To le

10Fig. 14Fig. 15Fig. 16 Fig. 17ROTATING TABLE FOR MITER CUTTINGYour miter saw will cut any angle from 90° to 47°, right and left. Pull out on the lock

11Fig. 18Fig. 19ADJUSTING 90° AND 45° DEGREE BEVEL STOPSDISCONNECT MACHINE FROM POWER SOURCE.1. Lock the machine in the “down” position.2. Place one e

12Fig. 23When bevel cutting, move the fence (A) Fig. 23 awayfrom the blade to allow for clearance for the saw bladeand guard. To accomplish this, lift

13Fig. 27ADJUSTING TENSION OF CUTTINGHEAD RETURN SPRINGThe tension of the cuttinghead return spring was set atthe factory to return to the “up” positi

14Holes are provided in the fence to attach an auxiliary fence. This auxiliary fence is constructed of straight woodapproximately 1/2" thick by 3

15Fig. 37 Fig. 38CUTTING ALUMINUMYou can easily cut aluminum extrusions (for makingaluminum screens and storm windows) with yourcompound miter saw. Wh

16CUTTING CROWN MOULDINGOne of the many features of a compound miter saw isthe ease of cutting crown molding.NOTE: The following procedure for inside

17STORAGEBLADE CHANGING WRENCH STORAGEYou can store the blade changing wrench (A) Fig. 47 in the slot (B) behind the fence (C).Fig. 47LOCKING CUTTINGH

1. Remove the screw (A) Fig. 50 and rotate the cover (B) to the rear (Fig. 51).2. Depress the arbor lock (A) Fig. 52 to lock the blade.3. Use the supp

19Fig. 55Fig. 562. The brushes are located in two holders (C) Fig. 55. Remove the spade type terminal connectors (D) and pull thebrush holders (C) out

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

20PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

31. FOR YOUR OWN SAFETY, READ THE INSTRUCT-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application,limitations, and specific hazar

4ADDITIONAL SAFETY RULES FORMITER SAWSRefer to them oftenand use them to instruct others.FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.04

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

6Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding type plug

7CARTON CONTENTSFig. 2Remove the miter saw and all loose items from the carton.Lifting the miter saw by the switch handle can cause misalignment. Alwa

8DUST BAGDepress the dust bag spring clips (A) Fig. 6, and secure the dust bag (B) between the ridges of the spout (C).Fig. 6WORK CLAMPTwo holes (A) a

9OPERATING CONTROLS AND ADJUSTMENTSHAZARD ZONEThe area inside the two red lines (A)Fig. 9 on the table is designated as a“Hazard Zone”. NEVER place yo