Delta 36-220 Manual de servicio

POWER TOOLSTECHNICAL DATAANDSERVICE MANUALCOMPOUND SAWC 10FC2SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENTLIST No. E927 May

--- 7 ---CAUTION For safe operation, see instruction manual. Do not expose to rain or use in damp locations.(1) Precautions on the Name PlateEach Mode

--- 8 ---8. ADJUSTMENT AND OPERATIONAL PRECAUTIONS8-1. Confirmation of Saw Blade Lower Limit PositioningThe lower limit of the saw blade cutting depth

--- 9 ---8-3. Cutting Operation(1) Cutting efficiency will be reduced if a dull saw blade is used, if an excessively long extension cord id used, or i

--- 10 ---(6) Compound (miter + bevel) cuttingCompound cutting can be accomplished by combining the miter cutting and bevel cutting operations descri

--- 11 ---9. ADJUSTMENT OF COMPONENTS9-1. Bevel Angle AdjustmentWhen shipped from the factory, the heights of 6 mmbolt (A) and 6 mm bolt (B) are adjus

--- 12 ---11. PRECAUTIONS IN DISASSEMBLY AND REASSEMBLY11-1. DisassemblySpecial attention in disassembly should be given to the following items.The ci

--- 13 ---1. Remove the two Tapping Screws (W/Washers) D5 x 20 [95] at theright and the two Machine Screws M4 x 20 [100]. Remove theHandle (Right) [

--- 14 ---1. Remove the two Machine Screws (W/Washer) M5 x 14 [39] andthe Chip Deflector [40] (debris guard).2. Remove the two Hex. Bolts (W/Washers)

--- 15 ---ItemNo.DisassemblyspotsDisassembly procedure Necessary tools4 TableBase6559586365666267607164Fig. 15PhillipsScrewdriver13 mm boxwrench616872

--- 16 ---1. Disassembly of the Armature Ass'y(1) Remove the two Brush Caps [136] and the two Carbon Brushes[135].(2) Remove the four Tapping Scr

REMARK:Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol(s)is(are) used in the place of company name(s) and model name(s)

--- 17 ---3. Disassembly of the Spindle Ass'y Remove the Spindle Ass'y [111] by gently tapping the Arm [120]with a plastic hammer.ItemNo.

--- 18 ---11-2. ReassemblyReassembly can be accomplished by following the disassembly procedures in reverse. However, specialattention should be give

--- 19 ---11-3. Wiring DiagramCarefully ensure that wiring is accomplished as illustrated below. As incorrect wiring will result in lack of rotation,

--- 20 ---11-5. No-load CurrentAfter no-load operation for 30 minutes, the no-load current values should be as follows.Voltage, FreauencyNo-load curre

--- 21 ---(4) Reassembly of the Table [60]When reassembling the Table [60] and the Base [74], tighten the Chuck Nut M8 [58] so that the Table [60]turn

--- 22 ---12. REPAIR GUIDEItemPhenomenon Cause (s)Inspection • Repair • Adjustment1 Inaccurate cutting...Inaccurate spuareness of cut surface...Cut

--- 23 ---ItemPhenomenon Cause (s)Inspection • Repair • Adjustment1 g Excessivemisalignment of thebase and the tablecauses the saw bladeto cut into t

--- 24 ---ItemPhenomenon Cause (s)Inspection • Repair • Adjustment d Excessively fastcutting speedFactorystandard---Reduce cutting speed. e Improper

--- 25 ---ItemPhenomenon Cause (s)Inspection • Repair • Adjustment a The power cord isnot connected topower supply.Factorystandard---Check power supp

--- 26 ---11. STANDARD REPAIR TIME (UNIT) SCHEDULESMODEL 10 20 30 40FixedVariableC 10FC2Work FlowHandleSwitchGeneral AssemblyFixed CostLinkBlade Guard

PageCONTENTS[ Business Section ]1. PRODUCT NAME•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

--- 27 ---Assembly Diagram for C 10FC2

--- 28 ---C 10FC2MOTOR ASS'YHOLDER ASS'Y

--- 29 ---PARTSC 10FC2ITEMNo.CODE NO. DESCRIPTIONNO.USEDREMARKS1 311-024 TRUSS HD. SCREW 1/4''X1/2'' 12 311-025 LINK 13 317-345 MA

--- 30 ---PARTSC 10FC2: ALTERNATIVE PARTSITEMNo.CODE NO. DESCRIPTIONNO.USEDREMARKS52 311-129 HEX. SOCKET SET SCREW M6X12 153 311-065 PIVOT SHAFT 154 9

--- 31 ---PARTSC 10FC2ITEMNO.CODE NO. DESCRIPTIONNO.USEDREMARKS102 317-382 VISE ASS’Y 1 INCLUD.103-110103 967-079 HEX. SOCKET SET SCREW M6X8 1104 311-

--- 32 ---: ALTERNATIVE PARTSC 10FC2ITEMNO.CODE NO. DESCRIPTIONNO.USEDREMARKS901 976-472TCT SAW BLADE CROSS-CUT 255MM-D15.9 HOLE1902 977-671TCT SAW BL

--- 1 ---1. PRODUCT NAMEHitachi Compound Saw, Model C 10FC22. MARKETING OBJECTIVEThe Model C 10FC2 was developed to upgrade and replace the current Mo

--- 2 ---4-1. Selling Point Descriptions(1) Press cuttingMakermodelMax. cuttingdimensionHeight x Width(H x W)HITACHIC 10FC267 x 146(2-5/8" x 5-3/

--- 3 ---MakermodelMax. cuttingdimensionLeft bevel 45Right/Left miter 45Height x Width(H x W)HITACHIC 10FC244 x 89(1-3/4" x 3-1/2")By turnin

--- 4 ---5. SPECIFICATIONSMaximumcuttingdimensionsHeight xWidth(H x W)0 (Right angle)Miter right/left 45Bevel left 45Miter right/left 45+Bevel left 4

--- 5 ---6. COMPARISONS WITH SIMILAR PRODUCTSItemMaker/ModelMax.cuttingdimensionsHeightx Width(H x W)0 (Right angle)67 mm x 146 mm(2-5/8" x 5-3/

--- 6 ---ItemMaker/ModelStandard accessories 255 mm (10") TCTsaw blade (24 teeth)for wood andaluminum cutting Dust bag Vise ass'y WrenchHITA